Ticket #104 (closed task)

Opened 8 years ago

modprobe no error but lsmod is empty (Examined/Solved - sensors 2.4.5 linux 2.2.13 i686)

Reported by: contact Owned by: somebody
Priority: minor Milestone:
Component: kernel Version:
Keywords: Cc:

Description

have a gateway with PIII 450, quite new. compiled all mods for separate loading, i2c first, did install, then lmsensors and did install. no compile or install errors on slackware 7. ran sensor-detect as root, and it "failed.":

We can start with probing for (PCI) I2C or SMBus adapters. You do not need any special privileges for this. Do you want to probe now? (YES/no): YES

Probing for PCI bus adapters... Use driver 'i2c-piix4' for device 00:07.3: Intel 82371AB PIIX4 ACPI Use driver 'i2c-voodoo3' for device 01:00.0: 3Dfx Voodoo3 Probe succesfully concluded.

We will now try to load each adapter module in turn.

Load 'i2c-piix4' (say NO if built into your kernel)? (YES/no): YES Loading failed ()... skipping. Load 'i2c-voodoo3' (say NO if built into your kernel)? (YES/no): YES Loading failed ()... skipping.

Do you now want to be prompted for non-detectable adapters? (yes/NO): yes

Load 'i2c-elektor' (say NO if built into your kernel)? (YES/no): Loading failed ()... skipping. [break]

i2c-dev is not loaded. Do you want to load it now? (YES/no): YES Loading failed (), expect problems later on.

[break] Couldn't open /proc/bus/i2c?!? at /usr/local/sbin/sensors-detect line 2008, <STDIN> chunk 9. and here is dmesg: Linux version 2.2.13 (root@anderspw) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Sat Feb 19 10:20:24 EST 2000 Detected 447696907 Hz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 445.64 BogoMIPS Memory: 128200k/131008k available (840k kernel code, 416k reserved, 1512k data, 40k init) CPU: Intel Pentium III (Katmai) stepping 02 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.35a (19990819) Richard Gooch (rgooch@…) PCI: PCI BIOS revision 2.10 entry at 0xfd983 PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP NET4: AppleTalk? 0.18 for Linux NET4.0 Starting kswapd v 1.5 parport0: PC-style at 0x378 [SPP,ECP,ECPPS2] parport0: detected irq 7; use procfs to enable interrupt-driven operation. Detected PS/2 Mouse Port. Serial driver version 4.27 with no serial options enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configuredes1371: features: joystick 0x0 es1371: codec vendor CRY revision 3 es1371: codec features Headphone out 18bit DAC 18bit ADC es1371: stereo enhancement: no 3D stereo enhancement PIIX4: IDE controller on PCI bus 00 dev 39 PIIX4: not 100% native mode: will probe irqs later

ide0: BM-DMA at 0x1060-0x1067, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1068-0x106f, BIOS settings: hdc:DMA, hdd:pio

hda: WDC AC313500D, ATA DISK drive hdc: TOSHIBA DVD-ROM SD-M1202, ATAPI CDROM drive hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: WDC AC313500D, 12949MB w/1966kB Cache, CHS=1650/255/63, UDMA hdc: ATAPI 32X DVD-ROM drive, 256kB Cache Uniform CDROM driver Revision: 2.56 hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm hdd: The drive reports both 100663296 and 0 bytes as its capacity Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 eth0: 3c509 at 0x230 tag 1, 10baseT port, address 00 a0 24 98 21 95, IRQ 10. 3c509.c:1.16 (2.2) 2/3/98 becker@…. Partition check:

hda: hda1 hda2 < hda5 hda6 hda7 hda8 >

VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 40k freed Adding Swap: 128484k swap-space (priority -1) eth0: Setting Rx mode to 1 addresses. eth0: Setting Rx mode to 2 addresses. eth0: Setting Rx mode to 3 addresses. eth0: Setting Rx mode to 4 addresses. I normally have bt878 mods loaded, but unloaded them to try lm_sensors. makes no difference either way. when i modprobe any i2c mod, there is no error given, but lsmod shows nothing. what is going on? do i not have any sensors? thanks pete anderson --- It seems your modules are not located. Check /etc/modules.conf to see whether the right paths are included, and run depmod -a. Good luck,

Frodo

Note: See TracTickets for help on using tickets.